Every install and repair we do covers the wall system, not just the boards. That means the parts you cannot see get the same attention as the parts you can. Here is what is standard on our wood siding work in Oklahoma City.
We remove the old siding, haul it off, and inspect the sheathing underneath. Any rotted sections get replaced before new material goes up. This is the step that determines whether your new siding lasts twenty years or leaks in year three.
New house wrap goes over the sheathing, and we re-flash every window, door and penetration. Flashing is where most siding leaks start, so we detail it with the correct laps and sealant rather than relying on caulk alone to keep water out.
Every board we cut gets its end grain primed before it goes up. End grain soaks water like a straw, and back-priming is the single cheapest thing you can do to stop rotting wood at joints and corners. Cheap crews skip it.
We nail with a siding nailer at the manufacturer's specified depth and leave a 1/8-inch gap at butt joints so boards can expand in summer humidity without buckling. A chalk line and level check every third course keeps the exposure even across the whole wall.
All joints, corners and penetrations get a bead from a caulk gun using exterior sealant rated for Oklahoma temperature swings. Then we apply your chosen stain or paint in two coats, sprayed and back-brushed for even coverage on textured wood.
We magnet-sweep for nails, haul off all debris, and walk the house with you course by course. You get touch-up stain for future repairs and written workmanship warranty paperwork before we pull out of the driveway.
Wood Siding in Oklahoma City is the exterior cladding system that covers your framed walls with cedar, redwood, pine or engineered wood boards, shakes or panels, fastened over house wrap and flashing to shed water and block wind. A correct install runs a chalk line for level, sets a siding gauge for consistent exposure, and leaves a 1/8-inch gap at butt joints so boards can move with humidity instead of buckling. We cut with a circular saw, nail with a siding nailer, and seal every penetration with caulk gun beads rated for Oklahoma temperature swings.
Most Oklahoma City wood siding calls we run are not new builds. They are 1970s ranch homes in Historic Capitol Hill with rotting wood around window trim, cedar that has gone gray and cracked after fifteen summers, or hail-bruised panels from a May storm that insurance already wrote a check for. If you are pricing wood siding replacement Oklahoma City wide, we walk the house, probe the sheathing with a pry bar, and tell you what is salvageable. Homeowners searching for wood siding installation near me Oklahoma City usually need two or three elevations redone, not the whole house.
Five steps, no surprises. You know what happens each day, who is on site, and when we clean up.
Schedule
Call or book online — a real human picks up and confirms a 2-hour arrival window.
Diagnose
Licensed tech inspects on-site, then walks you through the cause and your options.
Fix
The job is completed to code and done right the first time — no shortcuts, no surprises.
Guarantee
Every job backed by a written workmanship warranty — and we stand behind it.
Siding nailer
Drives nails to the exact depth the manufacturer specifies without over-driving and crushing the wood face. Consistent depth is what keeps boards from working loose in Oklahoma wind.
Circular saw
Cuts boards to length and rips them to width for odd runs. We finish cut ends with a utility knife and back-prime them before install.
Siding gauge and chalk line
Sets consistent course exposure and keeps every row level across the wall. A gauge is the difference between a wall that reads straight and one that drifts.
Pry bar
Probes for soft wood during the estimate and lifts boards without damaging adjacent courses during repair work.
Caulk gun
Applies exterior sealant at joints, corners and penetrations. We use sealant rated for the temperature swings Oklahoma City sees from January to August.
Tin snips
Cuts flashing and metal trim cleanly at window and door openings, which is where most water infiltration starts.
Level and hammer
Checks every third course for plumb and sets trim and corner boards. Small tools, but they are what keep the finished wall square.
IRC flashing and fastening details
We follow International Residential Code requirements for flashing laps, drainage planes and fastener spacing on every wall we open. That is the standard your inspector and your insurance adjuster both recognize.
Back-priming and gap installation
Every cut end gets primed and every butt joint gets a 1/8-inch gap. This lets the wood move with humidity instead of buckling and stops end-grain water absorption, which is the leading cause of rot at joints.
EPA Lead-Safe work practices
On pre-1978 homes, which are common around Historic Capitol Hill and Uptown 23rd, we contain the work area and follow EPA Lead-Safe handling and cleanup procedures during tear-off and repair.
Manufacturer system installation
We install James Hardie and LP SmartSide systems to the manufacturer's published details so the material warranty stays valid. Deviating from those details is how homeowners lose coverage on a claim.
01
What we do: We probe the full wall, replace the boards that are too far gone, and re-stain the rest with a breathable finish. Where the cedar is sound, refinishing saves thousands over full replacement.
→ The house looks restored rather than patched, and the finish holds for five to seven years with a light maintenance coat in between.
02
What we do: We tarp the same day, document the impacts with dated photos, meet the adjuster, and order matched material. Repair happens as soon as the claim clears, usually within a week.
→ The repaired elevation matches the rest of the house, the claim is clean, and no water got behind the wall while you waited.
03
What we do: We replace the two most visible elevations in cedar, repair the rest, and stain everything to a single consistent color so the house reads as one finished exterior in listing photos.
→ Higher list price support and faster showings, without paying for a full-house replacement you will not recoup.
04
What we do: We cut out the rot, treat the framing, re-flash the openings, and install matched boards back-primed on all cut ends. Repair is scoped tight and priced per section.
→ Watertight within a day or two, tenant stays in place, and the repair holds until the next full exterior cycle.
Oklahoma City sits in a climate that punishes exteriors from both ends. Summer UV hits 105 degrees and bakes the south and west walls, while winter drops to 15 degrees and drives freeze-thaw cycles into every joint. Add hail season from March through June and 40-mile-per-hour straight-line winds, and you get a city where siding takes real abuse. The housing stock matters too: 1920s bungalows in Paseo Arts District and Uptown 23rd have original cedar that has been refinished a dozen times, while 1970s ranches in Historic Capitol Hill often have the first replacement layer still on the wall. We size fasteners and flashing for wind ratings, back-prime every cut, and gap joints for movement. If you are pricing wood siding replacement Oklahoma City wide, ask any contractor how they handle expansion gaps and end-grain priming. The answer tells you whether the job will last.
Paseo Arts District
Historic bungalows with original cedar trim and shakes. We match profiles closely because the architecture is protected and visible from the street.
Historic Capitol Hill
Older housing stock with pre-1978 paint, so EPA Lead-Safe practices apply on every tear-off and repair we run here.
Midtown
A mix of restored bungalows and newer infill. We often blend cedar accents with fiber cement on the less visible elevations to balance cost.
Deep Deuce
Newer builds with engineered wood that take hail on the west and north elevations. Matched-material repair keeps the elevation uniform.
Hail season from March through June
Cedar bruises and engineered wood punctures, so we inspect from a ladder after every major storm and document impacts with dated photos for insurance claims.
Summer UV and 100-degree heat
Finish breaks down fastest on south and west walls. We recommend a breathable stain and plan on a recoat every five to seven years rather than waiting for peeling to start.
Winter freeze-thaw from 15 to 40 degrees
Water in joints expands overnight and opens gaps. Back-priming cut ends and leaving a 1/8-inch gap is what prevents the buckling and rot that follow.
Straight-line winds and spring storms
Loose panels and failed fasteners let wind-driven rain behind the wall. We fasten to the manufacturer's wind rating and check every course by hand before we leave.
Wood fails in predictable ways here, and most of it traces back to water getting in where it should not. Here is what we see most often and how we handle it.
Problem
Soft wood lets water into the framing, which leads to mold and mildew inside the wall and eventually structural repair that costs far more than new siding.
Our Fix
We cut out the rotted sections back to sound wood, treat the framing, re-flash the opening, and install new back-primed boards. If the rot runs deeper than the siding, we tell you before we cover it up.
Problem
Once the stain fails, UV breaks down the wood fibers and boards cup, crack and gray out. Repainting over a failing coat traps moisture and makes the peeling worse within a year.
Our Fix
We wash the wall, scrape and sand the failed areas, replace any boards that are too far gone, and apply two coats of breathable stain. Prepping correctly is what makes the finish last five to seven years instead of two.
Problem
Hail bruises cedar and punches through engineered wood, and loose panels let wind-driven rain straight into the wall. Left alone, one damaged elevation turns into a full replacement.
Our Fix
We inspect from a ladder, mark every impact, and document with dated photos for your adjuster. Then we replace only the damaged boards with matched material so the repair blends into the existing wall.
Problem
Water that gets behind the wall soaks the sheathing and insulation, which drives up energy bills and creates the conditions for mold and mildew that you cannot see from outside.
Our Fix
We pull the affected siding, find the entry point, and correct the flashing and house wrap detail that failed. Then we reinstall with proper laps and drainage so water sheds off the wall instead of into it.
Wood is the only siding that can be sanded, patched and re-stained instead of torn off and landfilled. Here is what that means for an Oklahoma City house in 2026.
Repairable, not disposable
A cracked cedar shake gets swapped in twenty minutes. Vinyl siding panels crack at 10 degrees and cannot be patched invisibly, so a single hail hit means replacing a whole run. With wood, we pull the damaged board, cut a match, and nail it in. That is why wood siding repair Oklahoma City OK near me searches spike every June after storm season.
Curb appeal that appraises
Appraisers in Oklahoma County treat cedar and engineered wood as a premium exterior. On a Midtown bungalow, a fresh stained cedar facade routinely supports a higher list price than the same house wrapped in vinyl. Buyers can see the difference from the curb, and it photographs better than flat panel siding in listing photos.
Handles Oklahoma freeze-thaw
Oklahoma City swings from 15 degrees in January to 105 in July. Wood moves with that cycle instead of fighting it. We install with a 1/8-inch expansion gap at every joint and back-prime the cut ends, which stops the warping and rotting wood you see on cheap installs that skipped that step.
Stains and paints refresh it
A quality stain job every five to seven years keeps cedar looking new for decades. That is far cheaper than re-siding. We prep with a wash, replace any soft boards, and spray two coats of breathable stain so moisture escapes instead of getting trapped and feeding mold and mildew behind the wall.
Google ★★★★★4.9
Replaced cedar on our Paseo bungalow and matched the profile perfectly. Crew was on site at 7:30 every morning and cleaned up each day. The written scope with photos made it easy to see exactly what we were paying for.
Yelp ★★★★★4.8
Hail took out our west wall in May. They tarped the same day, handled the adjuster meeting, and had matched boards up within a week of the claim clearing. No patch line visible at all.
BBB ★★★★★4.9
Got three bids for full replacement. Theirs was the only one that included re-flashing the windows in writing. Five-day install, no surprises, and the house is quieter inside now.
Google ★★★★★5.0
Called about a soft corner on a rental in Capitol Hill. They probed the whole wall, showed me photos, and repaired only what was actually bad. Honest pricing and the repair has held through two winters.
Elite Siding OKC has been installing and repairing exteriors in Oklahoma City since 2021. In five years we have worked on bungalows in Paseo Arts District, new builds in Deep Deuce, and storm-damaged ranches across Oklahoma County. Our crews are trained on James Hardie and LP SmartSide systems, and we follow IRC flashing details on every wall we open. We are a state-licensed Oklahoma contractor and carry EPA Lead-Safe certification for pre-1978 homes, which matters on the older housing stock around Historic Capitol Hill and Uptown 23rd.
Real experiences from customers who chose our Wood Siding services.
“Our 1928 bungalow had cedar that had gone gray and soft around two windows. Elite Siding OKC probed the whole wall, replaced about 40 boards, and re-stained the front and south elevations. They matched the profile so well you cannot tell where the new cedar starts. Finished in four days and cleaned up every scrap.”
Marcus T.
Homeowner, Paseo Arts District
“We got three bids for wood siding replacement and theirs was the only one that included re-flashing the windows. That detail sold me. Crew was on site at 7:30 each morning, and the job took five working days for the whole house. The house is noticeably quieter inside now, and the stain color came out exactly like the sample.”
Danielle R.
Homeowner, Midtown
“May hail beat up our engineered wood on the west side. They tarped it the same afternoon I called, took dated photos for my adjuster, and had the new boards up within a week of the claim clearing. Matched the existing color and you cannot see the repair line. Straight shooters.”
Kevin S.
Homeowner, Historic Capitol Hill
Real answers to the questions we hear most often from local homeowners and property managers.
Vinyl siding panels cost less than wood up front and never need staining, which makes them a common alternative when a homeowner wants the look refreshed without the upkeep. We install it over the same house wrap and flashing we use on wood jobs, so the wall behind it stays dry either way.
View Vinyl SidingFiber cement boards take paint well and resist hail better than wood, which matters in Oklahoma County storm season. Many homeowners pair fiber cement on the weather sides with cedar accents on the front elevation, giving them durability where it counts and real wood curb appeal where it shows.
View Fiber Cement SidingAluminum coils wrap fascia, soffit and trim on older Oklahoma City homes, and they often sit right next to wood siding. When we replace wood, we check the aluminum trim for dents and loose fasteners and re-secure or replace it so the new siding lines up clean at every edge.
View Aluminum SidingSteel siding panels stand up to hail that would bruise cedar, so they are worth pricing if your roof gets hit every few years. We install them with the same flashing details and can match them to wood accents on gables and porch ceilings for a mixed-material look.
View Metal / Steel SidingStone veneer on a foundation wall or porch column pairs well with cedar above it, and the contrast is popular on Midtown and Plaza District remodels. We flash the transition between stone and wood carefully so water sheds off the stone and never wicks up into the wood.
View Stone Veneer SidingBoard and batten is a vertical wood profile that suits modern builds and Craftsman remodels alike. We set the battens on 16-inch centers over house wrap, caulk the vertical seams, and back-prime every cut so the pattern stays crisp through Oklahoma humidity swings.
View Board and Batten SidingCall (405) 931-0174 or send us a note and we will get back to you the same business day. We answer the phone from 8 a.m. to 6 p.m. Monday through Friday, and we check messages on weekends. Free estimates across Oklahoma City and Oklahoma County.
Phone
(405) 931-0174Address
3150 W Memorial Rd Suite 210-186, Oklahoma City, OK 73134
Hours
Mon–Fri: 7AM – 7PM
Sat: 8AM – 4PM
Sun: Emergency Only
24/7 Emergency Available