Every board and batten job we do in Oklahoma City starts with the wall, not the panel. Here is what is covered in a standard install, and what we price separately if your home needs it.
We remove the old siding, haul it away, and recycle what we can. Tear-off lets us see the sheathing and flashing, which is where most hidden damage lives. On a typical Oklahoma City home, tear-off adds one to two days to the schedule.
New house wrap goes on every wall, with seams taped and windows and doors flashed. This is the layer that keeps water out of your walls. We use flashing tape and metal flashing at every penetration, including hose bibs, vents, and light fixtures.
We install the panel system you chose, whether that is fiber cement, vinyl, or engineered wood. Panels are fastened on the manufacturer's schedule, battens cover the seams, and every joint is caulked with a paintable sealant. Trim and corners are included.
J-channel, corner trim, and soffit trim are cut and fit on site. We bend aluminum coil for custom pieces so the edges look finished, not pieced. Trim is where a cheap install shows, so we take the extra time to get the miters tight.
We magnet-sweep the yard for nails, haul off scrap, and walk every wall with you. You get care instructions and our workmanship warranty in writing. If you spot something after we leave, call us and we will come back.
Board and batten siding is a vertical panel system where wide boards are nailed side by side and narrow strips, called battens, cover the seams between them. That batten is what sheds water and creates the deep shadow lines people recognize. We install it in fiber cement boards, vinyl siding panels, and engineered wood, and we fasten every panel to a flat, wrapped wall so the siding moves with the house instead of fighting it. On a typical Oklahoma City home, a full board and batten install takes three to six days depending on square footage and how much trim work is involved.
Oklahoma City homes take a beating that board and batten has to be built for. Spring hail, 70 mph straight-line winds, and summer heat that pushes 100 degrees all work on the panels, the caulk joints, and the fasteners. If your current siding is cracking and peeling, warping, or you can see daylight through the seams, that is usually a sign the original install skipped the house wrap or used the wrong fasteners. We see it constantly in older homes around Historic Capitol Hill and Stockyards City, where a board and batten siding replacement Oklahoma City project usually means fixing the wall behind the siding before we hang anything new.
You get a written scope, a start date, and a crew that shows up when we say we will. Here is exactly what happens from the first call to the final walkthrough.
Schedule
Call or book online — a real human picks up and confirms a 2-hour arrival window.
Diagnose
Licensed tech inspects on-site, then walks you through the cause and your options.
Fix
The job is completed to code and done right the first time — no shortcuts, no surprises.
Guarantee
Every job backed by a written workmanship warranty — and we stand behind it.
Siding Nailer
Drives ring-shank nails to the correct depth without overdriving. Overdriven nails crack panels and void warranties, so we set the depth on a test board before every wall.
Chalk Line and Level
The first board has to be dead plumb or the whole wall runs out of square. We snap a chalk line, check it with a 4-foot level, and adjust before we fasten anything.
Circular Saw and Tin Snips
Circular saw with a fiber cement blade for panel cuts, tin snips for aluminum coil trim. We cut outside and wear respirators when cutting fiber cement, per OSHA silica rules.
Caulk Gun and Siding Gauge
The caulk gun lays a consistent bead on every batten edge. The siding gauge keeps the reveal consistent so the shadow lines look even across the whole wall.
Pry Bar and Utility Knife
Used during tear-off to remove old siding without damaging the sheathing underneath. Careful tear-off saves you money on sheathing repairs.
IRC Wind Fastening Schedule
We fasten panels to the studs at the spacing the International Residential Code requires for your wind zone. Oklahoma City sits in a higher wind zone, so we do not cut corners on nail spacing. This is the single biggest factor in whether board and batten survives a storm.
James Hardie and LP SmartSide Systems
When we install fiber cement or engineered wood, we follow the manufacturer's published installation manual, including clearance from grade and roof lines. Following the manual is what keeps your material warranty valid.
EPA Lead-Safe Practices
Homes built before 1978 may have lead paint under the siding. We test, contain the work area, and follow EPA Lead-Safe rules on those jobs. Most of Historic Capitol Hill and Stockyards City falls into this category.
Flashing and Weep Detail
Every window, door, and penetration gets flashing tape and a weep path so water drains out instead of sitting behind the panel. This is the detail that separates a 30-year wall from a 10-year wall.
01
What we do: We tear off the old wood, replace the rotted sheathing, install new house wrap and flashing, and hang fiber cement board and batten. The whole job takes about a week, including paint.
→ The homeowner gets a modern facade that matches the neighborhood's character, and the rot problem is fixed at the source instead of covered up.
02
What we do: We document the hail damage for the insurance claim, then replace the damaged walls with fiber cement board and batten in a color the owner picked. We match the existing trim profile where we can.
→ The claim covers most of the cost, and the homeowner ends up with a better material than what was originally on the house.
03
What we do: We measure the existing board and batten, match the panel width and batten spacing, and install the same system on the new wall. We blend the caulk and paint so the seam is invisible.
→ The addition looks original to the house, and the owner avoids the mismatched-siding look that hurts resale value.
04
What we do: We price both fiber cement and vinyl board and batten, explain the repaint cycle on each, and let them choose. Vinyl costs less up front; fiber cement lasts longer and looks better up close.
→ The owner picks the material that fits their budget and long-term plans, with no pressure either way.
Oklahoma City sits in a hail and high-wind zone, and that shapes every board and batten job we do. We fasten to a tighter schedule than crews in calmer climates, we use ring-shank nails instead of staples, and we caulk with a sealant rated for the temperature swings we get between January and July. Spring storm season is the busiest time for board and batten repair Oklahoma City OK near me calls, because hail chips fiber cement and high wind pulls loose panels. If you are planning a new install, late fall and winter are the easiest times to get on the schedule. Summer installs are fine, but crews start early to beat the heat, and paint needs to go on before the wall gets too hot. Building stock matters too: homes in Bricktown and Automobile Alley are often brick with wood-frame gables, so board and batten usually goes on the gable and addition walls rather than the whole house. Homes in the Paseo Arts District and Historic Capitol Hill are more likely to be full re-sides, and many of them need sheathing repair once the old siding comes off. We pull permits where the City of Oklahoma City requires them and build to current IRC and IBC standards. If you want board and batten installation in Deep Deuce or anywhere else in Oklahoma County, we will walk the wall with you and tell you what it actually needs.
Bricktown
Mostly brick warehouses and newer lofts, so board and batten usually goes on gable ends and additions rather than full walls. We match the trim profile to the existing brick detailing.
Paseo Arts District
Older bungalows with original wood siding. Many need sheathing repair once the old siding comes off, and the neighborhood's color palette favors deep greens and blues on board and batten.
Deep Deuce
Newer construction with builder-grade vinyl. Hail damage is common here, and fiber cement board and batten is a popular upgrade after an insurance claim.
Historic Capitol Hill
Pre-1978 homes, so EPA Lead-Safe practices apply. We test for lead paint before tear-off and contain the work area. Many of these homes need full re-sides.
Most board and batten failures we see in Oklahoma City trace back to the same few causes: water behind the panels, bad fastening, or skipped flashing. Here is what we run into and how we fix it.
Problem
Wet sheathing rots, insulation loses R-value, and mold can grow inside the wall. By the time you see a stain on the ceiling, the damage has been spreading for months.
Our Fix
We tear off the affected section, replace the rotted sheathing, install new house wrap and flashing, and re-hang the board and batten. We also check every window and door above the damage, because that is usually where the water got in.
Problem
A panel that lifts in a storm can peel off and take the next one with it. Once the fasteners pull through, the wall is exposed and the next rain goes straight into the sheathing.
Our Fix
We re-fasten the wall to the correct schedule, replacing any pulled or overdriven nails. If the original install used staples or the wrong nails, we re-nail the whole run. We also check the battens, since they take the first wind load.
Problem
Paint failure on fiber cement usually means moisture is getting in from behind or the panel was not primed at the cut edges. Left alone, the board absorbs water and the problem spreads across the wall.
Our Fix
We find the moisture source first, fix the flashing or caulk line, then prep and repaint the affected area. Cut edges get primed before they go up on every job we do, which is why our paint jobs last.
Problem
Hail chips fiber cement and dents vinyl. Small chips let water into the panel core, and dents in vinyl can crack later. Insurance may cover it, but only if the damage is documented properly.
Our Fix
We photograph every impacted wall, note the panel type and age, and give you a repair scope for your adjuster. If the damage is widespread, we will tell you whether a full replacement makes more sense than patching.
Board and batten is not just a look. Done right, it is one of the most weather-resistant siding profiles you can put on an Oklahoma home, and it holds its color through years of UV exposure and freeze-thaw cycles.
Handles Oklahoma Wind
Vertical panels with properly set battens and ring-shank nails resist wind uplift far better than wide horizontal laps. We fasten to studs at the manufacturer's schedule, usually every 12 to 16 inches, and we use a siding gauge so no nail gets overdriven. That is the difference between siding that stays put in a 70 mph gust and siding that peels off in sheets.
Hides Wall Imperfections
The battens break up the wall into narrow vertical strips, so small dips and waves in the sheathing disappear. On older Oklahoma City homes with plaster or uneven framing, that matters. Instead of paying to re-skin the whole wall flat, board and batten gives you a clean, modern face with far less prep work and less material waste.
Paints and Repaints Clean
Fiber cement board and batten takes paint like a dream and holds it. We caulk every batten edge with a paintable sealant, then the painter rolls two coats. When it is time to refresh in eight to ten years, you wash it, spot-prime any bare spots, and paint again. No stripping, no sanding back to bare wood, no rot repair unless water got behind it.
Adds Real Curb Appeal
Vertical board and batten reads as modern farmhouse, craftsman, or contemporary depending on the trim and color you pick. Realtors in Uptown 23rd and Automobile Alley will tell you the same thing: a clean board and batten facade photographs well and helps a listing stand out. It is one of the few siding upgrades that looks intentional rather than builder-grade.
Google ★★★★★4.9
Elite Siding OKC replaced our old wood siding with fiber cement board and batten. They found rot around two windows that the other bids missed, showed us photos, and fixed it. Finished in six days. The vertical lines look great and the caulk work is clean.
Yelp ★★★★★4.8
After the spring hail, our vinyl siding was cracked on three walls. Elite documented everything for our insurance claim and got the full replacement approved. We upgraded to board and batten and could not be happier. Crew was on time every day.
BBB ★★★★★5.0
We used Elite for board and batten on a garage addition in the Plaza District. They matched the panel width and batten spacing to the main house perfectly. You cannot tell where the old siding ends and the new begins. Fair price, no surprises.
Google ★★★★★4.9
Called for an estimate on a Monday, had a written number by Wednesday, and the crew started the following week. They replaced rotted sheathing on the north wall and installed board and batten in a color we picked. Cleaned up every nail. Would use again.
Elite Siding OKC has been installing siding in Oklahoma City since 2021. In that time we have hung board and batten on bungalows in the Paseo Arts District, new builds in Deep Deuce, and everything in between. We are a state-licensed Oklahoma contractor, and our crews are trained on fiber cement and vinyl systems from James Hardie, LP SmartSide, CertainTeed, and Mastic. We know what Oklahoma hail does to a caulk joint, and we build for it.
Real experiences from customers who chose our Board and Batten Siding services.
“We had three bids for board and batten on our 1920s bungalow. Elite Siding OKC was the only one who talked about the house wrap and the flashing before the panels. They found rotten sheathing on the north wall, showed us photos, fixed it, and still finished in five days. The vertical lines look sharp and the caulk work is clean.”
Marcus T.
Homeowner, Midtown
“Our old vinyl was cracking and peeling after last spring's hail. Elite replaced it with fiber cement board and batten and painted it a deep green. They documented the hail damage for our insurance claim, which helped us get the full replacement covered. Crew was polite, cleaned up every nail, and the price matched the estimate exactly.”
Danielle R.
Homeowner, Paseo Arts District
“I wanted the modern board and batten siding Oklahoma City look for a new addition. Elite handled the whole thing, from the insulation board to the trim. They worked around our schedule and finished the gable in two days. Six months later, after a 60 mph wind event, not one panel moved. That tells you the fastening was done right.”
Kevin S.
Homeowner, Deep Deuce
Real answers to the questions we hear most often from local homeowners and property managers.
Vinyl is the most affordable way to get the board and batten look in Oklahoma City. Modern vinyl panels come in vertical profiles with deep shadow lines, and they never need paint. We install them with the same wall prep and flashing we use on fiber cement.
View Vinyl SidingFiber cement is the premium board and batten material. It is heavy, hail-resistant, and takes paint beautifully. James Hardie and CertainTeed both make vertical board and batten panels, and we install them with the correct fastening schedule for Oklahoma wind loads.
View Fiber Cement SidingReal wood board and batten, including cedar, gives the warmest look but needs staining every few years in Oklahoma's sun. We install it on porches, gables, and accent walls where the natural grain matters, and we seal every end cut to slow moisture wicking.
View Wood SidingAluminum coils are mostly used for trim, fascia, and wrapping posts around board and batten. Aluminum will not rot or rust, and it holds paint well. We bend custom trim on site so the edges around your board and batten panels look sharp, not pieced together.
View Aluminum SidingSteel siding panels come in vertical profiles that mimic board and batten and stand up to hail better than almost anything else. If you want the look without the repainting, steel is worth pricing. We install it with matching trim and fasteners rated for Oklahoma weather.
View Metal / Steel SidingStone veneer pairs well with board and batten on the lower half of a wall or around a porch column. The contrast between stone and vertical siding is one of the most requested looks in Oklahoma City right now. We flash the transition so water never sits behind the stone.
View Stone Veneer SidingCall (405) 931-0174 or send us a note and we will get back to you the same business day. We answer the phone from 8 a.m. to 6 p.m. Monday through Friday, and we check messages on weekends. Free estimates across Oklahoma City and Oklahoma County.
Phone
(405) 931-0174Address
3150 W Memorial Rd Suite 210-186, Oklahoma City, OK 73134
Hours
Mon–Fri: 7AM – 7PM
Sat: 8AM – 4PM
Sun: Emergency Only
24/7 Emergency Available
