Tear-Off and Disposal
We remove the existing siding, trim, and any failed flashing in the veneer zone, then haul it off. If we find rotted sheathing or soft framing, we document it with photos and quote the repair before we close the wall back up.
Licensed
Licensed & Bonded
Fully Insured
Insured & Bonded
24/7 Emergency
Same-Day Response
Warranty Backed
5+ Years Trusted in Oklahoma City
What Our Stone Veneer Siding Service Includes
Every stone veneer job we run includes the full assembly, not just the stone. Here is what is covered in a standard scope, and what we quote separately when the wall needs it.
House Wrap and Flashing
New house wrap goes over the sheathing, then flashing at every window head, door, and penetration. We install a weep screed at the base so water that gets behind the stone drains out instead of sitting against your framing.
Lath and Scratch Coat
Metal lath is fastened over the wrap, then a scratch coat of mortar is troweled on and cured. This is the layer that holds the stone and distributes the load. We do not skip the cure time, even when the schedule is tight.
Stone Setting and Cutting
The crew sets stone course by course off a level and chalk line, cutting with a circular saw or tin snips and packing joints with mortar. We keep the mortar color consistent across the wall so the finished facade reads as one piece.
Clean-Up and Walkthrough
We wash the wall, scrub mortar haze off adjacent brick and trim, and magnet-sweep the yard for nails. Then we walk the job with you, explain the care instructions, and hand over the warranty paperwork before we leave.
Stone Veneer Siding in Oklahoma City: What It Actually Is
Stone Veneer Siding in Oklahoma City is a lightweight masonry cladding that mimics natural stone and hangs off your wall on a drainage plane instead of carrying load. We start with house wrap, then flashing, then metal lath, then a scratch coat of mortar, and finally the stone itself. You get the look of a limestone or fieldstone facade at roughly a third of the weight, which matters on older Oklahoma County homes that were never framed for full bed-depth stone. Every course gets leveled and every corner gets cut with a circular saw or tin snips so the joints stay tight.
Oklahoma City homes take a beating that coastal veneer guides never mention. Hail the size of golf balls, 100-degree July afternoons, and ice storms that drop 30 degrees in six hours all work on the mortar and the substrate. We build for that. If you have been searching for stone veneer siding near me Oklahoma City and finding thin galleries with no real specs, this page is the one that tells you what goes behind the stone. We also repair failed veneer from other installers.
How Our Stone Veneer Installation Process Runs
Five stages, one crew, no mystery. Here is exactly what happens from the first measurement to the final wash-down.
01
Schedule
Call or book online — a real human picks up and confirms a 2-hour arrival window.
02
Diagnose
Licensed tech inspects on-site, then walks you through the cause and your options.
03
Fix
The job is completed to code and done right the first time — no shortcuts, no surprises.
04
Guarantee
Every job backed by a written workmanship warranty — and we stand behind it.
Tools and Methods We Use for Stone Veneer
Tools & Equipment
Siding Nailer
Drives lath and trim fasteners at consistent depth without over-driving. Over-driven fasteners tear the house wrap and create a leak path, so we set the depth and check it on every wall.
Circular Saw with Masonry Blade
Cuts stone veneer to length and angle for corners, window returns, and the top course. A sharp blade keeps the cut face clean so the joint reads tight instead of chipped.
Tin Snips and Utility Knife
Trim flashing, house wrap, and lath to fit around penetrations. Clean cuts are what make the flashing details watertight instead of taped-over and hoping.
Level and Chalk Line
Establish the first course and keep every course above it true. Stone veneer that wanders off level is the most visible installation failure there is, and it is entirely preventable.
Caulk Gun and Mortar Bag
Pack joints and seal the transitions where stone meets trim, windows, and doors. We use a mortar bag for the joints and a caulk gun for the flexible seals that need to move with the wall.
Pry Bar and Siding Gauge
Remove old cladding without damaging the sheathing and set the exposure on any adjacent lap siding. The gauge keeps the transition between stone and siding consistent across the wall.
Methods & Standards
Adhered Veneer over Metal Lath
The standard method for most Oklahoma City homes. We fasten lath over house wrap, trowel a scratch coat, and set the stone in mortar. It is lighter than anchored veneer and works on standard wood-framed walls without a foundation ledge.
Anchored Veneer with Brick Ties
For full-height stone on new construction or a wall built for it, we anchor the veneer with brick ties and a drainage cavity. This is the method IBC and IRC describe for structural masonry veneer, and it is what we use when the wall is designed for it.
Rainscreen and Weep Screed Detailing
We install a continuous drainage plane with a weep screed at the base and flashing at every penetration. Water that gets behind the stone drains out at the bottom instead of sitting against the sheathing. This one detail is the difference between a 40-year facade and a 10-year one.
Mortar Mix and Cure Control
We mix mortar to the manufacturer's spec and control the cure with moisture and shade, especially in July and August when Oklahoma City hits 100 degrees. Rushing the cure is why cheap veneer cracks in the first freeze-thaw cycle.
When Oklahoma City Homeowners Call Us for Stone Veneer
01
A homeowner in Historic Capitol Hill wants to cover a cracked, painted foundation wall on a 1920s bungalow.
What we do: We install a stone veneer skirt over new house wrap and flashing, tying it into the existing brick above. The stone covers the cracks, hides the patchwork paint, and gives the house a period-correct base that matches the neighborhood.
→ The foundation reads as original masonry, the cracks are gone, and the homeowner stops repainting the base every three years.
02
A Deep Deuce new build has a flat, plain front elevation that looks like every other house on the street.
What we do: We add a stone veneer accent on the entry column and the lower front wall, using a limestone-look profile that contrasts the fiber cement above. We detail the transition so the two materials meet on a clean line.
→ The house reads as custom from the street, and the stone handles hail that would dent the aluminum on the neighboring builds.
03
A property manager in Bricktown needs stone veneer repair after a storm knocked a section loose near a corner.
What we do: We remove the loose stone, inspect the lath and sheathing, re-flash the corner, and re-set the stone to match the existing wall. We photograph everything and write the scope for the insurance claim.
→ The repair is invisible, the claim is documented, and the corner is watertight before the next storm season.
04
A homeowner in the Plaza District is tired of vinyl siding panels cracking every time it hails.
What we do: We tear off the vinyl on the front elevation, repair the sheathing, and install stone veneer over a full drainage plane. The sides and back keep vinyl to control cost, and we match the trim across both.
→ The front wall survives hail that would have destroyed the old vinyl, and the house looks like a full remodel for a fraction of the cost.
How Stone Veneer Siding Runs in Oklahoma City
Oklahoma City sits in a climate that swings hard: 100-degree July afternoons, ice storms in January, and hail that can arrive any month from March through October. That cycle is hard on any cladding, and it is why we build stone veneer over a full drainage plane with a weep screed instead of gluing stone to the wall. The building stock matters too. In Historic Capitol Hill and the Paseo Arts District we work on 1920s bungalows with pier-and-beam foundations and original wood sheathing, so we inspect for rot before we cover anything. In Deep Deuce and Automobile Alley the homes are newer and framed for modern cladding, which lets us use anchored veneer on full-height walls. Oklahoma County permits follow IBC and IRC masonry veneer provisions, and we pull them and pass inspection. If you are comparing stone veneer contractor Oklahoma City OK options, ask what goes behind the stone. That answer tells you whether the facade will last 40 years or 10.
Neighborhoods We Serve
-
Historic Capitol Hill
1920s bungalows with original wood sheathing and pier-and-beam foundations. We inspect for rot and repair framing before we set any stone on these walls.
-
Paseo Arts District
Historic stucco and wood exteriors where stone veneer has to match the existing texture. We sample the mortar color before we start so the new work blends with the old.
-
Deep Deuce
Newer construction framed for modern cladding. These walls can take anchored veneer at full height, which gives a heavier, more permanent look than an accent-only install.
-
Automobile Alley
Mixed-use and modern residential builds where stone veneer pairs with metal siding. We detail the transition so the two materials meet on a straight, watertight line.
Local Conditions We Plan For
-
Hail season from March through October
Stone veneer survives most hail that destroys vinyl and aluminum, but the trim and flashing around it can take damage. We inspect those details after every major storm and document anything for your insurance claim.
-
Freeze-thaw cycles in January and February
Water that gets behind the veneer and freezes will push stone off the wall. The weep screed and drainage plane we install are what let that water escape before it freezes.
-
100-degree summer afternoons on west-facing walls
Mortar cures too fast in direct July sun and cracks. We control the cure with moisture and shade, and we add insulation board behind the lath to cut the radiant heat load.
Cracked Foundation Wall to Stone Skirt
Stone Veneer Problems We Fix in Oklahoma City
Most failed stone veneer we see in Oklahoma City was installed without a drainage plane or with the wrong lath. Here are the problems we get called for most.
Problem
Water infiltration behind the stone
Trapped water rots sheathing and framing, grows mold and mildew, and eventually pushes the veneer off the wall. By the time you see it inside, the damage is usually a $3,000 to $8,000 repair.
Our Fix
We remove the affected stone, inspect the sheathing, replace what is rotted, and rebuild the assembly with house wrap, flashing, and a weep screed. Then we re-set the stone and match it to the existing wall so the repair disappears.
Problem
Cracking and peeling mortar joints
Open joints let water in and make the facade look tired. On south and west walls in Oklahoma City, thermal swing opens joints within a few years if the mortar was mixed wrong or the wall was not cured.
Our Fix
We grind out the failed joints, re-point with a matching mortar, and seal where the spec calls for it. If the cracking traces back to a missing drainage plane, we fix the root cause, not just the surface.
Problem
Loose stone after hail or wind
A loose stone is a falling hazard and a sign the lath or scratch coat failed. Ignoring it usually means more stones come off in the next storm, and the repair scope grows with every one.
Our Fix
We remove the loose stones, check the lath and scratch coat underneath, and re-set them with fresh mortar. If the lath itself failed, we rebuild that section of the assembly. We document the damage for your insurance claim.
Problem
Veneer installed over rotted wood
Some installers cover rot instead of fixing it. The rot keeps spreading behind the stone, and the veneer starts to sag or crack within two or three seasons. The fix is always more expensive than the original repair would have been.
Our Fix
We open the wall, replace the rotted wood, treat the framing, and rebuild the assembly correctly. It costs more up front than a cosmetic patch, but it is the only repair that lasts.
Why Oklahoma City Homeowners Choose Stone Veneer
Stone veneer changes how a house reads from the curb and how it holds up through a decade of Oklahoma weather. Here is what you actually get.
-
Curb Appeal That Appraises
A stone veneer accent on the entry or the front foundation wall is one of the few exterior upgrades that shows up in an appraisal. Oklahoma City stone veneer company work on the front elevation routinely moves a listing photo from forgettable to first-click. We match the stone to your brick, your roof, and your trim so it looks original, not bolted on.
-
Hail and Wind Resistance
Adhered veneer over proper lath handles hail far better than vinyl panels that crack at 1 inch and aluminum that dents. After the last big Oklahoma County hail event we replaced panels on dozens of homes; stone facades on the same street needed only mortar touch-up. That is a real difference in your insurance math over 10 years.
-
No Rot, No Repaint
Stone veneer does not rot like cedar shakes, does not fade like vinyl siding panels, and does not need repainting every 5 to 7 years. Wash it once a year with a garden hose and a soft brush. For homeowners tired of scraping and caulking, stone veneer installation Oklahoma City wide is the last exterior finish they buy for a long time.
-
Insulation and Thermal Mass
We install insulation board behind the lath on most jobs, which adds R-value and cuts the radiant heat that bakes west-facing walls in August. Stone also holds temperature, so the wall stays steadier through a 25-degree overnight swing. Your HVAC runs less in both July and January.
Licensed, Insured, and Documented
Licensed & Certified
- State of Oklahoma Contractor License — issued by Oklahoma Construction Industries Board
- General Liability and Workers Compensation Insurance — issued by Active policy on file for every job
- IBC and IRC Masonry Veneer Compliance — issued by International Code Council standards followed on every install
- EPA Lead-Safe Practices — issued by Required for pre-1978 homes in Historic Capitol Hill and the Paseo Arts District
Verified Reviews
Google ★★★★★4.9
Elite Siding OKC installed stone veneer on our front wall after hail destroyed the vinyl. They explained the drainage plane, showed us photos of the sheathing repair, and finished in five days. The stone looks like it came with the house. Worth every dollar.
Google ★★★★★5.0
We had water getting behind an old stone wall for years. Elite found the missing weep screed, rebuilt the base, and re-set the loose stone. No leaks through two springs now. They know what they are doing behind the stone, not just on the surface.
BBB ★★★★★4.8
Fair quote, clear scope, no surprises. They matched the existing stone on a repair and you cannot tell where the new work starts. Cleaned up the yard better than they found it. I have recommended them to two neighbors already.
Five Years of Oklahoma Siding Work
Elite Siding OKC has been installing and repairing exterior cladding in Oklahoma City since 2021. In that time we have worked on bungalows in Historic Capitol Hill, new builds in Deep Deuce, and everything between. Our crews are trained on adhered veneer and anchored veneer, and we follow IBC and IRC masonry veneer provisions on every job. We are an Oklahoma-licensed contractor, and we carry the insurance and bonding that let us pull permits and pass inspection without drama. When a hail claim needs documentation, we write the scope in the language adjusters accept.
- Licensed Oklahoma contractor with active insurance and bonding on file
- Trained on IBC and IRC adhered veneer and anchored veneer standards
- Five years of Oklahoma City exterior work, including post-hail rebuilds
- Crews fluent in flashing, weep screed, and drainage-plane detailing
- Direct insurance-claim documentation for hail and storm damage
What Oklahoma City Homeowners Say
Real experiences from customers who chose our Stone Veneer Siding services.
“We had hail take out the vinyl on the front of our 1940s house, and Elite Siding OKC replaced it with stone veneer on the lower wall. They flashed everything, put in a weep screed, and the wall has not leaked through two springs. The stone looks like it was always there. They finished in five days and cleaned up every nail.”
M
Marcus T.
Homeowner, Uptown 23rd
“I got three quotes for stone veneer siding near me and Elite was the only one who talked about what goes behind the stone. They found rotted sheathing under the old siding, fixed it, and showed me photos. The entry column and foundation skirt look great. Fair price, no surprises on the invoice.”
D
Danielle R.
Homeowner, Paseo Arts District
“We manage several rentals and needed stone veneer repair after a storm knocked a section loose. Elite Siding OKC matched the existing stone, re-flashed the corner, and had it done in two days. They documented everything for our insurance claim. I have used them on three properties since.”
K
Kevin S.
Property Manager, Bricktown
Frequently Asked Questions About Stone Veneer Siding
Real answers to the questions we hear most often from local homeowners and property managers.
How much does Stone Veneer Siding Installation cost in Oklahoma City OK?
Most full stone veneer installations in Oklahoma City run $18 to $32 per square foot installed in 2026, so a 400-square-foot facade lands between $7,200 and $12,800. Accent walls and foundation skirts cost less because there is less prep and less cutting. Tear-off, sheathing repair, and scaffolding push the number up. We give you a written scope with a firm number before we start.
Is stone veneer good for Oklahoma weather?
Yes, when it is installed over a proper drainage plane. Oklahoma's freeze-thaw cycles and hail are hard on thin cladding, but adhered veneer over lath and mortar handles both. The failure mode is water trapped behind the stone, which is why we flash every penetration and install a weep screed at the base. Done right, stone veneer outlasts vinyl and fiber cement in this climate.
How long does stone veneer last in Oklahoma City?
A properly installed stone veneer facade lasts 30 to 50 years in Oklahoma City. The stone itself will outlive the house. What fails first is mortar joints on south and west walls that take the most sun and thermal swing, and those are repairable without tearing the wall apart. We inspect and re-point joints as part of our siding maintenance service.
Who installs stone veneer siding in Oklahoma City?
Elite Siding OKC installs stone veneer across Oklahoma City and Oklahoma County, including Bricktown, Midtown, the Paseo Arts District, and Uptown 23rd. We have been doing exterior work here since 2021 and handle everything from a single accent wall to a full facade replacement. Call (405) 931-0174 for a free measurement and a written scope.
Related Siding Services
Vinyl Siding
Vinyl is the budget option for the walls you are not stoning. We often run vinyl siding panels on the sides and back of an Oklahoma City home and stone veneer on the front elevation, which keeps the budget in check while the street-facing wall gets the upgrade.
View Vinyl SidingFiber Cement Siding
Fiber cement boards from James Hardie pair well with stone veneer because both handle Oklahoma hail and sun. We frequently install fiber cement on the upper gable and stone on the lower wall, giving you a two-tone facade that reads custom without a custom price.
View Fiber Cement SidingWood Siding
Cedar shakes and wood siding give a warm, historic look that fits Paseo Arts District and Historic Capitol Hill homes. We install wood on the gables and stone on the foundation and entry, then seal both so Oklahoma humidity does not drive rot behind the veneer.
View Wood SidingAluminum Siding
Aluminum coils and steel siding panels are common on mid-century Oklahoma City homes. When we add stone veneer, we remove the aluminum in the veneer zone, repair the sheathing, and tie the new flashing into the existing aluminum so the transition is watertight.
View Aluminum SidingMetal / Steel Siding
Metal siding handles hail better than almost anything, and it pairs cleanly with stone veneer on modern builds in Automobile Alley and Deep Deuce. We detail the transition so the two materials meet on a straight line and the flashing behind both stays continuous.
View Metal / Steel SidingBoard and Batten Siding
Board and batten on the upper story with stone veneer below is one of the most requested combinations we build in Oklahoma City. The vertical lines contrast the stone texture, and both materials take hail without the cracking you see on vinyl panels.
View Board and Batten SidingContact Elite Siding OKC
Call (405) 931-0174 or send us a note and we will get back to you the same business day. We answer the phone from 8 a.m. to 6 p.m. Monday through Friday, and we check messages on weekends. Free estimates across Oklahoma City and Oklahoma County.
Elite Siding OKC
-
Phone
(405) 931-0174 -
Address
3150 W Memorial Rd Suite 210-186, Oklahoma City, OK 73134
-
Hours
Mon–Fri: 7AM – 7PM
Sat: 8AM – 4PM
Sun: Emergency Only
24/7 Emergency Available